Galvanic Isolation
Isolated 72V 60V 48V to 24V DC-DC Buck Step Down Converter
- Input Range36V – 96V DC
- Nominal Output24V DC Steady
- TopologyOpto-Isolated Buck
23+
Years Power Electronics R&D
96.8%
Peak Power Factor Efficiency
10+
Precision Production Lines
ISO 9001
SGS Verified Inspection Benchmarks
Engineered Deployments
High-Performance AC/DC & Power Conversion Equipment
Pre-tested, burn-in verified modular rectifiers, converters, and power management modules calibrated for telecom, renewable integration, and industrial infrastructure across Greater Copenhagen.
Dynamic Buck-Boost
9-32VDC to 12VDC 12A 144W Auto Buck-Boost Converter
- Wide Window9V – 32V DC
- Rated Current12A Stabilized
- EnclosureSealed Extruded Al
Compact Module
8-35V to 7V 5A Step Down DC-DC Power Supply Module
- Input DC8V – 35V DC
- Output Rating7V DC / 5A (35W)
- Thermal Coeff.±0.02%/°C
Pure Sine Inverter
600W–5000W Industrial Heavy-Duty DC to AC Pure Sine Inverter
- DC Options12V / 24V / 48V DC
- AC Voltage230VAC 50Hz True Sine
- Surge Overhead200% for 3 seconds
Marine & Fleet
12V/24V to 13.8V 10A Automotive & Marine Voltage Stabilizer
- Target Battery13.8V Float Charging
- Amperage10A Continuous
- ProtectionOVP, OCP, Reverse Pol.
High Voltage Input
Wide Input 48V–96V to 12V 5A 60W Isolated Converter
- HV Bus Input48V / 60V / 72V / 96V
- Aux Supply12V DC Regulated 5A
- Isolation Hipot1500VDC Input/Output
Solar Hybrid Rectifier
3KW 48VDC All-in-One Hybrid Inverter-Rectifier with LCD
- AC Input230VAC Utility/Genset
- DC Bus Output48VDC Modular Array
- ControllerBuilt-in MPPT + PFC
IP67 Waterproof
Ruggedized IP67 Waterproof 24V to 12V 3A DC Micro Converter
- ProtectionFull Epoxy Resin Seal
- Efficiency≥95% Ultra Low Loss
- MountingVibration Proof Flange
AC to DC Rectifier Systems: High-Efficiency Grid Conversion for the Greater Copenhagen Region
In modern critical power architecture, the industrial AC to DC rectifier system is the cornerstone of telecom backbone operations, distributed microgrid stations, railway interlocking infrastructure, and edge data facilities. Serving Copenhagen and the broader Zealand (Sjælland) industrial zone, our high-frequency switched-mode power supplies (SMPS) bridge high-voltage AC mains (230V single-phase / 400V three-phase 50Hz) to continuous, ripple-free, galvanically isolated DC power busses—primarily 24VDC, 48VDC, 110VDC, and 220VDC.
Unlike legacy thyristor rectifiers that suffer from heavy magnetics and lagging power factors, our advanced rectifier modular topologies utilize Active Power Factor Correction (PFC ≥ 0.99) and zero-voltage resonance switching (ZVS). This guarantees compliance with stringent Danish electrical energy conservation guidelines, ensuring Total Harmonic Distortion (THDi) remains strictly below 3%, thus protecting municipal transformers and upstream networks from electrical noise.
| Operational Metric | Varnix Switch-Mode Rectifiers | Legacy Silicon-Controlled (SCR) | Commercial OEM Standards |
|---|---|---|---|
| Electrical Conversion Efficiency | 95.5% – 97.2% Peak Efficiency | 82% – 87% (High Heat Dissipation) | 90% – 93% |
| Input Power Factor (cos φ) | ≥ 0.99 at 30%–100% Load Window | 0.70 – 0.82 (Requires Capacitor Banks) | ≥ 0.94 |
| Total Harmonic Distortion (THDi) | ≤ 3.0% under EN 61000-3-2 | > 28% (Generates Severe Harmonics) | ≤ 7.0% |
| System Redundancy Architecture | Modular N+1 / N+2 Hot-Pluggable | Centralized Single-Point Unit | Fixed Modular Configurations |
| Monitoring & Interface | SNMP v3, Modbus-TCP, RS485, WebGUI | Basic Analog Dry Contacts | RS232 / Proprietary Bus |
Local Infrastructure
Mission-Critical Applications across Copenhagen & Denmark
Tailored power electronics meeting the specific climatic, infrastructural, and regulatory requirements of the Nordic maritime environment.
⚗
District Energy & Thermal Storage Integration
Copenhagen’s world-renowned district heating systems (such as HOFOR networks) increasingly utilize decentralized pumping stations, smart telemetry, and actuator valves requiring 24VDC and 48VDC uninterruptible backbones. Our isolated DC-DC converters and rack rectifiers operate reliably under severe temperature fluctuations without loss of conversion accuracy.
📶
5G Densification & Coastal Telecom Infrastructure
As TDC Net and regional carriers expand urban 5G micro-cells across Østerbro, Vesterbro, and coastal Amager, telecom-grade embedded rectifiers supply uninterrupted -48V DC bus power. Featuring anti-corrosive conformal coatings, they withstand humid coastal maritime saline conditions without breakdown.
⚙
Nordic Maritime, Harbor & Ferry Electrification
With Port of Copenhagen focusing on shore-to-ship clean power and autonomous electric harbor ferries, our wide-input marine DC-DC voltage regulators stabilize onboard auxiliary electronics, navigation suites, and sensor nodes against harsh voltage surges from battery charging lines.
Industry Horizon
Regional Technology & Energy Trends (2025–2030)
How regulatory shifts and sustainability mandates are reshaping rectifier acquisition in Denmark.
🌱
The Net-Zero Data Center Mandate
Denmark is an international hub for hyperscale green facilities. Municipal environmental standards demand minimal heat waste. High-efficiency rectifiers (>96%) significantly lower Power Usage Effectiveness (PUE) scores, aligning directly with Denmark’s climate targets.
🔌
Grid Ancillary Services & Hybrid Battery Storage
With Danish wind penetration reaching global records, volatility requires rapid frequency response. Modern AC/DC rectifier subsystems integrate bi-directional and fast-charging parameters to harmonize industrial battery storage (BESS) directly with Energinet grid expectations.
🛡
Cybersecure SCADA & Networked Power Management
Danish procurement managers now reject closed systems. The transition toward NIS2 compliance requires secure network monitoring protocols (SNMP v3, encrypted HTTPS, and Modbus TCP) built directly into rectifier supervisory controller units (CSUs).
2003
Established Base
Enterprise Reliability
Engineered to Surpass European Quality Expectations
Founded in 2003, Varnix Technology Co., Ltd. operates a high-precision manufacturing complex spanning 1,229 m² verified onsite by SGS. We specialize in robust, high-frequency switching architecture engineered specifically for global commercial markets that cannot afford power downtime.
Every AC to DC rectifier and DC-DC converter passes five strict stages of internal quality control: automated incoming component evaluation, high-grade wave soldering, computerized functional validation, full-load high-temperature burn-in, and final insulation resistance testing under CE, RoHS, and FCC protocols.
- ISO 9001:2015 Quality System
- 100% Full-Load Burn-In Testing
- Complete OEM / ODM Customization
- 98.2% Direct Engineering Response
Procurement Clarity
Frequently Asked Questions for Copenhagen & Danish Buyers
Practical guidance addressing customs, safety regulations, lead times, and engineering parameters.
What certifications do your rectifiers hold for deployment in Denmark?
All our AC to DC rectifier systems, power supplies, and DC-DC converters carry comprehensive CE conformity declarations, RoHS compliance verification, and test documentation according to the Low Voltage Directive (LVD 2014/35/EU) and Electromagnetic Compatibility Directive (EMC 2014/30/EU). Our facilities are certified to ISO 9001:2015, and on-site factory audits are verified by SGS Group.
How do you handle shipping, customs clearance, and DDP delivery into Greater Copenhagen?
We provide comprehensive international incoterms including FOB, CIF, CFR, and fully managed DDP (Delivered Duty Paid) directly to your facilities or integration partners in Copenhagen, Glostrup, Taastrup, or elsewhere across Zealand. Customs clearance, import VAT handling, and localized freight forwarding are fully coordinated with established air and sea transport partners.
Can rectifier units be customized for non-standard DC voltages or dual battery chemistry?
Yes. We offer deep OEM/ODM engineering tailoring. We can build custom rectifiers with floating charge settings optimized for valve-regulated lead-acid (VRLA), gel, or lithium iron phosphate (LiFePO4) battery packs. Output profiles can be customized across 12V, 24V, 48V, 60V, 110V, and 220V with intelligent temperature-compensated charging.
What thermal protections exist for enclosed cabinet installations with low airflow?
Our rectifiers feature intelligent temperature-controlled forced-air cooling fans with speed profiling, combined with auto-derating firmware. If internal temperatures rise beyond calibrated safety thresholds due to HVAC or heat exchanger issues, the system smoothly throttles output current instead of abruptly shutting down, protecting critical loads until thermal balance is restored.
What is your minimum order quantity (MOQ) and sample lead time?
For standard catalog DC-DC converters and off-the-shelf industrial inverters, MOQs begin at 1 to 10 sets. For custom engineering OEM rectifier programs or high-power modular assemblies, we support fast prototyping with sample delivery windows typically within 10 to 18 business days from final schematic approval.
Accelerate Your Copenhagen Critical Power Project
Discuss your operational voltage, redundancy tier, modular footprint, and environmental requirements with a senior Varnix power systems specialist today.
Get a Quote